Great Offer, Buy Trojan MS-2000 Cheapest
You can buy it here ! Our shop offers the best thing for you here. Shop best deals of Trojan MS-2000 You can buy it now with special price in stock , best price Trojan MS-2000 for sale fast shipping in usa only and might get free shipping service.. Read more...
Now to get best price offer! Buy Trojan MS-2000 Now
Ratings
Category: Tools & Home Improvement
Brand: Trojan
Model: MS-2000
Availability: In Stock
List Price :
Special Prices: Check Special Offers !!!
Trojan MS-2000 Customer reviews
Trojan MS-2000 Review by Toolpig "toolpig" (Troy , KS)
I've had an ms 2000 and the 2000x extension wing now for over three years. It has been very helpful on my jobs. It really makes for a smooth running cut station . I hate site built contraptions to elevate your saw and for material support. The ms 2000 is a very nice piece of equipment. It sets up in less than a minute. With or without the 2000x it offers solid material support for varied lengths with the ladder type slide out wings. With the 2000x it is outstanding even with heavy framing lumber. Many other stands only offer support for long stock with their rollers so far away from the saw. If you have a five foot or under cutoff , it falls to the ground where it might suffer damage. This stand is also the easiest I've seen to set up and break down. I sometimes work on sites where ther are several stands from many companies. It's so much faster it's not even funny. I know one carpenter who was planning on getting the rousseau stand. Two guys struggled for two minutes to get their rousseau folded up in front of us. I said watch this. I folded mine up in a fraction of the time , by myself and had it in the trailer before they were done. Needless to say he bought a Trojan. One outstanding benefit is the height. It is much taller than the other available stands. I like my work to be up high where I can see it without bending over. After years of use mine developed a little play in the lock mechanism. It was very easy to fix. Trojan can supply a new lock rod or you can disassemble it and drill a new hole for any one of the cotter pins . This makes the rod longer and tightens up the whole stand. The designer has since improved the locking mechanism to make it more rigid and resistant to wear. When I got my new Makita LS 1212 I considered getting a different stand. Nothing really compared very well so I bought another Trojan. I'm happy I did!
Trojan MS-2000 Review by James Bernier (Maine)
Trojan has thought of so many great features and it is well built but does move some. Whether shifting the saw on its miter gage or positioning the wood to saw,it. It kind of twists on its wheels. There are three delta 50-155 universal stands on our crew of finish carpenters. These are solid stands though they lack many features the Trojan has. I have the 12"Dewalt sliding compound on the stand and it is a big saw. The mobility is great and not that it feels unsafe. Its just that the Delta stands theas are solid.
Trojan MS-2000 Review by Victor H. Agresti "remodeling-guy" (Gaithersburg, MD United States)
I bought a rolling miter stand because my heavy DeWalt sliding double compound saw was too heavy to lug around; also, plywood on sawhorses makes a lousy stand, and using a miter saw sitting on the floor isn't as productive as a stand. I've had a Trojan stand since 2001.
CONs:
- Trojan should use high-quality plywood for the table instead of half inch MDF. MDF looks cheap, the edges can break off, and you wouldn't want it to get wet.
- There is a chance the entire rig could topple over while unfolding the stand with a mounted saw, as the stand has to be tilted over on one end and held there so it doesn't fall over, while you lock the leg-spreader bar, then pull the whole assembly upright. I haven't come close to dropping it (yet?), but if it fell over, the attached saw could be damaged.
- The stand isn't designed to be stored in the upright position, as there is no "foot" to hold it in place. I store mine in a semi-upright position (65 degrees), where the stand rests on it's wheels and a roller. Thus stored, the stand isn't all that stable and it takes 37" of space from the wall with a Dewalt DW708 mounted.
- Stand lacks a handle when it's being used as a hand-truck. One of the rollers serves that purpose, but an actual handle would be better.
- The 1" square tubing next to the wheels was too long. It would scrape the ground unless the stand was on a perfectly smooth surface. I cut a half inch off each side at the same angle, and reattached the plastic bumpers.
- Concerned that the Trojan-supplied wheel caps might come off, I installed cotter pins. Probably not necessary, but now the wheels are securely held on.
Here's how: Center-punch a dent into the axle, quarter inch from each end, to guide a drill bit. Drill a 1/8" hole through the axle - with a drill press if you have one. Slide axle into stand holes, install the spacer washers provided by Trojan, slide wheels onto axle, put a 0.5" washer over each end of the axle, insert a 3/32" cotter pin into the hole and bend it over. (See customer photo above).
PROs:
- Initial set-up was straightforward, it came with all the parts, and it was easy to adjust the height of the end rollers to match the height of my miter saw.
- Any miter saw should work on this stand after adjusting the rollers to match the saw's table height. Since every brand/model saw is different, you'll have to drill the holes to match your saw's mounting holes. Use carriage bolts/wing nuts to secure the saw to the table, so it's easily removable.
- I can open-up the Trojan with saw attached, by myself, in about 30 seconds, and that's being careful (to prevent the rig from falling over). Takes slightly longer to fold it up. It rolls as easily as a hand truck when folded, although since I'm tall, I have to lean over to grab the roller (used as a handle).
- My DeWalt miter saw stays bolted to the Trojan, since it's so easy to roll and set-up. With the Trojan's large rubber tires, I can also [carefully] move the saw up and down stairs by myself, even inside a finished house.
- For cutting short pieces of stock, neither 32-inch table extension is needed. Otherwise, all you have to do is unscrew a T handle bolt to lift an extension in place, align its height against the saw's bed by eye, and tighten the handle. Takes about 10 seconds per side. The excellent extensions have cross bracing to provide multiple points of support for varying lengths of work. For really long pieces, I also use a separate work stand, not attached to the Trojan.
- If you will ever need to use your miter stand outside on soft (but close to level) ground, consider getting one with large tires that stay down when the table is opened up (Trojan MS2000, Rousseau 2950, or Delta 36-136). Stands that rest on 4 legs when opened (HTC HP-575PK or Delta 50-155) might sink into a soft surface (such as grass) when setting it up - OR - tip over once set up. With the Trojan, you won't need a piece of wood under the tires for increased stability. If the ground isn't level, prop up one tire and one side of the other end for firm base, with a small piece of plywood or other scrap.
Another benefit of a stand with tires that stay on the ground: you can then roll the opened stand to a different location. E.g., #1 - store the stand/saw set-up in a nearby secure location for the duration of a job. Then when starting work, roll the stand/saw where it's most convenient. E.g. #2 - if the stand isn't exactly where you want it, roll it there, without folding it up. Stands like the HTC or Delta 50-155 are unwieldy to move once they are opened, especially if you're alone.
- I'm 6' 4" tall and find the Trojan's height perfect -- the miter saw's table is 39 inches off the ground.
- Everything folds up into a single compact unit, so there's nothing else to carry or remember to take, and nothing pokes out to get in your way (like the extension rollers on the Rousseau 2950).
Summary: A well thought out functionally designed product that improves productivity -- primarily because it sets up quickly and has large rubber tires that stay on the ground.
The Delta 36-136 Universal Miter Saw Stand should also be on your short list...
More Reviews...
Trojan MS-2000 Miter Saw Stand:: Description
Trojan MS2000 Miter Saw Stand, Innovative design for maximum portability, Galvanized rollers - won't rust, Durable powder coat and zinc plated finish, "Cart" rather than "carry" your saw to the job, Fast, time saving set up, Easily rolls up stairs and over debris. Large 16" x 40" MDF tabletop & has 10" pneumatic tires. Saw NOT Included.
Trojan MS-2000 Miter Saw Stand:: Features
- Can be used with a variety of saws
- 10-inch pneumatic wheels for portability
- Sturdy steel-tubing construction
- Easy setup
- Provides 13-feet of overall support
- Brand: Trojan
- Model: MS-2000
- Product Type: Tools & Home Improvement
Trojan MS-2000:Buy today for save more!
Tags : Buy Trojan MS-2000, Best Buy Trojan MS-2000 Miter Saw Stand Lowest Price, Trojan MS-2000 On Sale, Trojan MS-2000 Miter Saw Stand Review, Great Deals Trojan MS-2000 Miter Saw Stand, Cheap Trojan MS-2000 Miter Saw Stand.
See also:
Gardena 1979-U
Qualcraft 2601 Best price!
Milwaukee 5615-20 Review
Palmgren 30601 Product reviews
Porter-Cable 893PK Customer reviews
Rajah II, Grivory Handle, Plain On Sale!
DEWALT DC820KA Customer reviews
Porter-Cable 9690LR Customer reviews
Ryobi P844 Best price!
LITB 006001649 Best price!
Fluke fluke 115 Customer reviews
Milwaukee 7150-21 Free Shipping !
Shop-Vac 9633400 Great Offer!
Milwaukee 6515-20 Review
Warehouse of Tiffany's 3046+BB1055 Sale!
Recent posts:
Product Jet 708718R youtube videoGreat Deal Oneway 2289 Sale amazon
